 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Solid Wire Grounding Assembly 2058729-1 11 408-10262 04 MAY 09 Rev A Instruction Sheet /32-in. Hex Washer Nut Wire Bolt Wire Slot The grounding assembly accepts solid uninsulated copper wire sizes 6 or 8 AWG. 9 /16-in. 3. INSTALLATION (See Figure 2) Hex Nut 1. Using a No. 11/64-in. drill bit, drill a (4.37+.203 [.172+.008]) hole in the frame. Threaded Post 2. Insert the thread post end of the wire bolt into the hole. 3. Thread the hex washer nut onto the threaded post end of the wire bolt. Finger-tighten. Figure 1 4. Position the wire into the wire slot. 5. Thread the hex nut onto the wire slot end of the wire bolt. Finger-tighten until the wire is compressed. 6. Using a 9/16-in. open end wrench, hold the hex body of the wire bolt, and using an 11/32-in. socket wrench, tighten the hex washer nut to a torque of 2.82 N-m [25 in.-lbs.]. 7. Continue holding the hex body, and using a socket wrench, tighten the hex nut to a torque of 5.08 N-m [45 in.-lbs.]. 9/ -in. 16 1. INTRODUCTION Solid Wire Grounding Assembly 2058729-1 is used with metal-framed photovoltaic (solar) panels and related products that require grounding for safety reasons. NOTE All numerical values in this instruction sheet are in metric units [with U.S. customary units in i brackets]. Dimensions are in millimeters [and inches]. Figures are not drawn to scale. 2. DESCRIPTION The grounding assembly consists of a wire bolt (wire slot on one end and threaded post on the other), 9/ -in. hex nut, and 11/ -in. hex washer nut. See 16 32 Figure 1. 4. REMOVAL 1. Using a 9/16-in. open end wrench, hold the hex body of the wire bolt, and using a 9/16-in. socket wrench, loosen the hex nut. Installation Wire 2 1 Frame 5 4 3 Figure 2 E2009 Tyco Electronics Corporation, Harrisburg, PA TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at All International Rights Reserved TE logo and Tyco Electronics are trademarks. 1 of 2 LOC B www.tycoelectronics.com *Trademark. Other products, logos, and company names used are the property of their respective owners. Solid Wire Grounding Assembly 2058729-1 2. Remove the wire from the wire slot. 3. Continue holding the hex body, and using an 11/ -in. socket wrench, loosen the hex washer 32 nut. Remove the wire bolt from the frame. 408-10262 Order replacement grounding assemblies through your representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 5. REPLACEMENT AND REPAIR The grounding assembly can be re-used up to 5 times after proper removals. The grounding assembly can not be repaired. DO NOT use defective or damaged product. 6. REVISION SUMMARY S Initial release of instruction sheet 2 of 2 Tyco Electronics Corporation Rev A |
Price & Availability of 2058729-1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |